Industry News2019-12-28T17:30:11+08:00


This is Why Some of the Fiber Laser Cutter Can Have Twice the Life

December 28th, 2019|

High-efficiency cutting not only depends on the performance and configuration of the product itself, the maintenance of the machine also plays an unshakable role. Today I will introduce to you how to extend the service life of the machine and reduce costs. Daily inspection and maintenance of machine tools 1)Daily check before starting: Check the pressure of the laser working gas and cutting gas. If the gas pressure is not enough, it should be replaced in time. Check whether the circulating water level in the chiller is sufficient. If not, it must be added in time. Check whether there is water leakage in the circulating waterway of the external light path, and it must be handled in time to prevent the water leakage from causinga short circuit of the electronic components. If cutting with compressed air, the air storage tank, and desiccant must be drained before starting.  2)Daily check on startup:  Check whether the voltage regulator is under voltage or over voltage. If there is any abnormality, please deal with it immediately and contact the manufacturer in time. [...]

4 THINGS You Must Know About Press Brakes

December 11th, 2019|

The press brake has been broadly used in many industries for a long time, but do you already know it well, and are you clear about the 4 things you must know about it and the 9 operating procedures and precautions? If not, it’s not too late, just read this article! What is a press brake? Press brake is a piece of forming machinery used to bend sheet and plate material according to different process requirements, mainly focusing on bending metal sheets, which follows the cutting process throughout the processing chain. How about it’s structure? What constitutes a press brake? A table for placing a sheet and an upper knife for pressing can finish the whole action? Of course not! Press brake consists of following main parts, including two C-frames form the sides, a table at the bottom and a movable beam at the top, matching fixtures, electrical system, hydraulic cylinder, hydraulic system, slider and guide mechanism, dies, back gauge, front support, compensation cylinder, etc. How many types of press brake? There are several types of brakes as [...]

How to solve emitting problem of laser cutting machine?

October 29th, 2019|

During the use of fiber laser cutting machine, the laser tube occasionally does not emit light, which may slow down the production schedule, causing the loss of Millions of dollars, affect the quality of the finished products and damage the company's reputation. It usually can be divided into several situations as below. First one is no light at a sudden, second one is the light used in the laser tube is getting weaker and weaker, and the last one is start using everything normally, no light after the next day. In the event of such a failure, the first thing to do is to check the machine itself, focusing on a few major parts, one is the chiller, the other is the power supply, and the third is the machine card. Follow the 5 steps below for details: Check whether the water is circulating normally, if not, repair it and make it resume running again. However, if the problem is occurred in water protection, it can be reused by shorting the water protection. Click the [...]

What is CO2 Laser?

September 27th, 2019|

Laser can be used not only for funny cats, but also for cutting, fiber laser can cut kinds of metal materials which we have referred before in What is fiber laser cutting machine? With different working principle, different types of laser cutter has relative specific performance, uses and corresponding maintenance method and COST. Today, we are going to talk about CO2 laser cutting, a long history and mature technology, invented in 1964. CO2 laser is famous for cutting non-metallic materials, for instance, cloth we wear, plexiglass product in our lives, the wooden fence we used to house the lamb, the leather we used to make shoes, and the ubiquitous plastic products in life, etc. CO2 laser cutting products are full of our lives, and influence them significantly. As CO2 laser influence people a lot, What is CO2 laser became an inevitable question people want to figure out. The gas laser is the first continuous optical laser and the first laser to operate on the principle of converting electrical energy into laser output.       1. Divided by working medium: According to [...]

What is fiber laser cutting machine?

August 30th, 2019|

What is fiber laser? The concept of fiber laser is as clueless as the mathematical knowledge in books, for a lot of low-proficiency learners of math. But in fact, it’s not that hard to learn, lasers are not only small boxes that shoot red dots, which drive cats crazy, but are also used in many manufacturing processes. They can be used to cut metals and non-metals. But how about “fiber laser cutting machine”? From the word “machine” we can guess that it’s a kind of equipment driven by gasoline or electricity to assist human production activities, which we all familiar with. And is this machine the same as the CO2 and YAG cutters? Not really! We have made a brief introduction of basic information before What is laser cutting, laser cutting machine and fiber laser cutting machine? And we are going to set forth more detail and specific content for you TODAY. It doesn’t matter if you are just learning this industry or if you already have known it well, even have many customers or have purchased many machines, it’s also basic and essential question you need [...]

What is laser cutting, laser cutting machine and fiber laser cutting machine?

June 6th, 2019|

Laser cutting refers to the use of a focused high-power-density laser beam to illuminate a workpiece, causing the irradiated material to rapidly melt, vaporize, ablate, or reach a burning point, while cutting the molten material by means of a high-speed airflow coaxial with the beam, thereby cutting the workpiece. Laser cutting is one of the hot cutting methods. Laser cutting works by directing the output of a high-power laser most commonly through optics. The [laser optics] and CNC (computer numerical control) are used to direct the material or the laser beam generated. There are three main types of lasers used in laser cutting. The CO2 laser is suited for cutting, boring, and engraving. The neodymium(Nd) and neodymium yttrium-aluminium-garnet (Nd:YAG) lasers are identical in style and differ only in application. Nd is used for boring and where high energy but low repetition are required. The Nd:YAG laser is used where very high power is needed and for boring and engraving. Both CO2 and Nd/Nd:YAG lasers can be used for welding. According to the different laser generators, the more conventional laser cutting machines on the market can be roughly divided into three types: [...]


 Fill out this form to get in touch.


Dongguan Shenzhen Suzhou




Dongguan Shenzhen Suzhou



We provide essential maintenance to all customers!


Contact Us